This patch augments the MESI_Three_Level Ruby protocol with hardware
transactional memory support.
The HTM implementation relies on buffering of speculative memory updates.
The core notifies the L0 cache controller that a new transaction has
started and the controller in turn places itself in transactional state
(htmTransactionalState := true).
When operating in transactional state, the usual MESI protocol changes
slightly. Lines loaded or stored are marked as part of a transaction's
read and write set respectively. If there is an invalidation request to
cache line in the read/write set, the transaction is marked as failed.
Similarly, if there is a read request by another core to a speculatively
written cache line, i.e. in the write set, the transaction is marked as
failed. If failed, all subsequent loads and stores from the core are
made benign, i.e. made into NOPS at the cache controller, and responses
are marked to indicate that the transactional state has failed. When the
core receives these marked responses, it generates a HtmFailureFault
with the reason for the transaction failure. Servicing this fault does
two things--
(a) Restores the architectural checkpoint
(b) Sends an HTM abort signal to the cache controller
The restoration includes all registers in the checkpoint as well as the
program counter of the instruction before the transaction started.
The abort signal is sent to the L0 cache controller and resets the
failed transactional state. It resets the transactional read and write
sets and invalidates any speculatively written cache lines. It also
exits the transactional state so that the MESI protocol operates as
usual.
Alternatively, if the instructions within a transaction complete without
triggering a HtmFailureFault, the transaction can be committed. The core
is responsible for notifying the cache controller that the transaction
is complete and the cache controller makes all speculative writes
visible to the rest of the system and exits the transactional state.
Notifting the cache controller is done through HtmCmd Requests which are
a subtype of Load Requests.
KUDOS:
The code is based on a previous pull request by Pradip Vallathol who
developed HTM and TSX support in Gem5 as part of his master’s thesis:
http://reviews.gem5.org/r/2308/index.html
JIRA: https://gem5.atlassian.net/browse/GEM5-587
Change-Id: Icc328df93363486e923b8bd54f4d77741d8f5650
Signed-off-by: Giacomo Travaglini <giacomo.travaglini@arm.com>
Reviewed-on: https://gem5-review.googlesource.com/c/public/gem5/+/30319
Reviewed-by: Jason Lowe-Power <power.jg@gmail.com>
Maintainer: Jason Lowe-Power <power.jg@gmail.com>
Tested-by: kokoro <noreply+kokoro@google.com>
Standardize all header guards in the mem directory according to the most
frequent patterns. In general they have the form:
mem: __FOLDER_TREE_FILE_NAME_HH__
ruby: __FOLDER_TREE_FILENAME_HH__
Change-Id: I983853e292deb302becf151bf0e970057dc24774
Reviewed-on: https://gem5-review.googlesource.com/7881
Reviewed-by: Nikos Nikoleris <nikos.nikoleris@arm.com>
Maintainer: Nikos Nikoleris <nikos.nikoleris@arm.com>
This patch eliminates the type Address defined by the ruby memory system.
This memory system would now use the type Addr that is in use by the
rest of the system.
This patch takes a first step in tightening up how we use the data
pointer in write packets. A const getter is added for the pointer
itself (getConstPtr), and a number of member functions are also made
const accordingly. In a range of places throughout the memory system
the new member is used.
The patch also removes the unused isReadWrite function.
This patch removes the parameter that enables bypassing the null check
in the Packet::getPtr method. A number of call sites assume the value
to be non-null.
The one odd case is the RubyTester, which issues zero-sized
prefetches(!), and despite being reads they had no valid data
pointer. This is now fixed, but the size oddity remains (unless anyone
object or has any good suggestions).
Finally, in the Ruby Sequencer, appropriate checks are made for flush
packets as they have no valid data pointer.
This patch tidies up random number generation to ensure that it is
done consistently throughout the code base. In essence this involves a
clean-up of Ruby, and some code simplifications in the traffic
generator.
As part of this patch a bunch of skewed distributions (off-by-one etc)
have been fixed.
Note that a single global random number generator is used, and that
the object instantiation order will impact the behaviour (the sequence
of numbers will be unaffected, but if module A calles random before
module B then they would obviously see a different outcome). The
dependency on the instantiation order is true in any case due to the
execution-model of gem5, so we leave it as is. Also note that the
global ranom generator is not thread safe at this point.
Regressions using the memtest, TrafficGen or any Ruby tester are
affected and will be updated accordingly.
This patch is as of now the final patch in the series of patches that replace
Time with Cycles.This patch further replaces Time with Cycles in Sequencer,
Profiler, different protocols and related entities.
Though Time has not been completely removed, the places where it is in use
seem benign as of now.
The patch started of with replacing Time with Cycles in the Consumer class.
But to get ruby to compile, the rest of the changes had to be carried out.
Subsequent patches will further this process, till we completely replace
Time with Cycles.
This patch was initiated so as to remove reference to g_system_ptr,
the pointer to Ruby System that is used for getting the current time.
That simple change actual requires changing a lot many things in slicc and
garnet. All these changes are related to how time is handled.
In most of the places, g_system_ptr has been replaced by another clock
object. The changes have been done under the assumption that all the
components in the memory system are on the same clock frequency, but the
actual clocks might be distributed.
This patch adds support to different entities in the ruby memory system
for more reliable functional read/write accesses. Only the simple network
has been augmented as of now. Later on Garnet will also support functional
accesses.
The patch adds functional access code to all the different types of messages
that protocols can send around. These messages are functionally accessed
by going through the buffers maintained by the network entities.
The patch also rectifies some of the bugs found in coherence protocols while
testing the patch.
With this patch applied, functional writes always succeed. But functional
reads can still fail.
This patch removes some of the unused typedefs. It also moves
some of the typedefs from Global.hh to TypeDefines.hh. The patch
also eliminates the file NodeID.hh.
The goal of the patch is to do away with the CacheMsg class currently in use
in coherence protocols. In place of CacheMsg, the RubyRequest class will used.
This class is already present in slicc_interface/RubyRequest.hh. In fact,
objects of class CacheMsg are generated by copying values from a RubyRequest
object.
This changeset contains a lot of different changes that are too
mingled to separate. They are:
1. Added MOESI_CMP_directory
I made the changes necessary to bring back MOESI_CMP_directory,
including adding a DMA controller. I got rid of MOESI_CMP_directory_m
and made MOESI_CMP_directory use a memory controller. Added a new
configuration for two level protocols in general, and
MOESI_CMP_directory in particular.
2. DMA Sequencer uses a generic SequencerMsg
I will eventually make the cache Sequencer use this type as well. It
doesn't contain an offset field, just a physical address and a length.
MI_example has been updated to deal with this.
3. Parameterized Controllers
SLICC controllers can now take custom parameters to use for mapping,
latencies, etc. Currently, only int parameters are supported.
This was done with an automated process, so there could be things that were
done in this tree in the past that didn't make it. One known regression
is that atomic memory operations do not seem to work properly anymore.
This basically means changing all #include statements and changing
autogenerated code so that it generates the correct paths. Because
slicc generates #includes, I had to hard code the include paths to
mem/protocol.
