This file is a required input to the simulator for GPUFS. There seems to
be confusion from several users who are not providing this input. This
usually results in the amdgpu driver failing to load, leading to the
application under test exiting along with it.
This changeset adds a simple md5 hashsum check to compare against the
known good MMIO trace located in the gem5-resources repository.
Change-Id: I59819fc795a6bc4bc6badbd4d120db1246498987
Reviewed-on: https://gem5-review.googlesource.com/c/public/gem5/+/69978
Tested-by: kokoro <noreply+kokoro@google.com>
Reviewed-by: Matt Sinclair <mattdsinclair@gmail.com>
Maintainer: Matt Sinclair <mattdsinclair@gmail.com>
An example case,
```python
mem_side_port = RequestPort(
"This port sends requests and " "receives responses"
)
```
This is the residue of running the python formatter.
This is done by finding all tokens matching the regex `"\s"(?![.;"])`
and manually replacing them by empty strings.
Change-Id: Icf223bbe889e5fa5749a81ef77aa6e721f38b549
Signed-off-by: Hoa Nguyen <hoanguyen@ucdavis.edu>
Reviewed-on: https://gem5-review.googlesource.com/c/public/gem5/+/66111
Reviewed-by: Bobby Bruce <bbruce@ucdavis.edu>
Maintainer: Bobby Bruce <bbruce@ucdavis.edu>
Tested-by: kokoro <noreply+kokoro@google.com>
The KVM CPU hangs if there are not multiple event queues when more than
one CPU is created. Since GPUFS primarily relies on the KVM CPU, support
for multiple event queues is needed. Some GPU libraries, such as AMD
Research's ATMI library, assume more than one CPU.
This changeset adds support for multiple CPUs and was tested for up to
four CPUs.
Change-Id: Ia354e02209d0fa18195f3ad44f4fb1d58e93b5ca
Reviewed-on: https://gem5-review.googlesource.com/c/public/gem5/+/65131
Maintainer: Jason Lowe-Power <power.jg@gmail.com>
Tested-by: kokoro <noreply+kokoro@google.com>
Maintainer: Matt Sinclair <mattdsinclair@gmail.com>
Reviewed-by: Matt Sinclair <mattdsinclair@gmail.com>
The disjoint VIPER configuration creates completely disconnected CPU and
GPU Ruby networks which can communicate only via the PCI bus. Either
garnet or simple network can be used. This copies most of the Ruby setup
from Ruby.py's create_system since creating disjoint networks is not
possible using Ruby.py.
Change-Id: Ibc23aa592f56554d088667d8e309ecdeb306da68
Reviewed-on: https://gem5-review.googlesource.com/c/public/gem5/+/53072
Reviewed-by: Jason Lowe-Power <power.jg@gmail.com>
Maintainer: Jason Lowe-Power <power.jg@gmail.com>
Tested-by: kokoro <noreply+kokoro@google.com>
Remove the line "For use for simulation and test purposes only" in files
were AMD is the only copyright holder listed in the header. This happens
to be the case for all files where this line exists, removing it
completely from gem5.
Change-Id: I623f266b002f564301b28774f49081099cfc60fd
Reviewed-on: https://gem5-review.googlesource.com/c/public/gem5/+/53943
Reviewed-by: Jason Lowe-Power <power.jg@gmail.com>
Maintainer: Jason Lowe-Power <power.jg@gmail.com>
Tested-by: kokoro <noreply+kokoro@google.com>
The flow for Full System amdgpu is the use KVM to boot linux and begin
loading the driver module. However, the amdgpu module requires reading
the VGA ROM located at 0xc0000 in X86. KVM does not support having a
small 128KiB hole at this location, therefore we take a checkpoint and
switch to a timing CPU to continue loading the drivers before the VGA
ROM is read.
This creates a checkpoint just before the first MMIOs. This is indicated
by three interrupts being sent to the PCI device. After three interrupts
in a row are counted a checkpoint exit event occurs. The interrupt
counter is reset if a non-interrupt PCI read is seen.
Change-Id: I23b320abe81ff6e766cb3f604eca2979339938e5
Reviewed-on: https://gem5-review.googlesource.com/c/public/gem5/+/46161
Reviewed-by: Matt Sinclair <mattdsinclair@gmail.com>
Reviewed-by: Jason Lowe-Power <power.jg@gmail.com>
Maintainer: Matt Sinclair <mattdsinclair@gmail.com>
Tested-by: kokoro <noreply+kokoro@google.com>
This is an initial configuration capable of booting Linux and
registering a PCI device which registers as an AMD Vega 10 (Frontier
Edition) GPU. It it loosely based on the the example/fs.py and gem5 book
full system example scripts. The top-level file is meant to be modular
such that convenience scripts can be created to set arguments
automatically and then call the main run function.
This will evolve over time as more full-system GPU components are added
and the network topology needed for disjoint address spaces is created
for the VIPER protocol.
Change-Id: I7002213ca8de5eb73919e49fb11840a688744012
Reviewed-on: https://gem5-review.googlesource.com/c/public/gem5/+/44907
Reviewed-by: Jason Lowe-Power <power.jg@gmail.com>
Reviewed-by: Matt Sinclair <mattdsinclair@gmail.com>
Maintainer: Jason Lowe-Power <power.jg@gmail.com>
Tested-by: kokoro <noreply+kokoro@google.com>
